Should I remove the roof tiles or splice and screw in new wood to fix this issue?
Asked by Minttu Kallio 
3 months ago
Last Updated: September 1, 2024
I could really use some guidance here. Should I take out the roof tiles or can I just add new wood with some splicing and screws? I’d appreciate your advice on this. Thanks in advance for your input.
Did you manage to repair the roof to prevent it from leaking? There isn’t much else you can do besides checking how far the good wood goes back and attaching a new 2×4. It appears that a drip edge is needed.
I think it’s time for a new roof … mine is around 28 years old…. I’ll begin seeking estimates once the rainy season is over
Appreciate it!
I think I would attach another piece and remove the decay. However, it might not appear perfect.
If he includes all of his sisters, it will at least have a symmetrical look. That style shouldn’t be too terrible
No content
Rosales scarf combo for the victory.
Rosales this exact point ^^^
No content
You could attach a 2×4 to the tails as reinforcement. If it were up to me, I would attach one on each side, remove the current one by 6 inches, and secure a new 6-inch piece with the existing ones or on both sides of the tails. Best of luck!
Check this out!
Hey , thanks for the great idea!
Hey , you’re welcome!
I notice this happening frequently in SoCal. I’ve observed termite repair professionals using Bondo to fix it, cutting off the damaged part and adding a new rafter tail, or completely replacing the rafter. They typically only work on the roof if the eave boards require replacement. In that case, they lift the roof slightly to install new boards.
I’ll probably end up tackling this with a different item. Appreciate it!
Let’s talk about why it’s leaking. 1) The design is not great 2) The rafter end should have been sloped to prevent water from continuously hitting the end grain of the 2×4. 3) I recommend doubling up on reinforcing it and patching in a piece to make the necessary repairs and strengthen the overall structure. 4) For a long-term solution, consider installing a fascia along the entire length. This will involve cutting back each rafter by 2 1/4″ to fit a 2×6 and a 1×2 under the roof’s edge, along with drip edge flashing. The 1×2 will create a 3/4″ setback that serves two purposes: redirecting water down the drip edge instead of onto your rafter tails, and providing a space to install gutters just below the 1×2 to prevent water contact with the surface. Hopefully, this explanation is clear to you.
Thanks…. Is it a silly question to ask if the decaying eaves are supporting the roof? I assume that since they’re rotted, they’re not providing much strength or structure, right?
Understands that even with decay, there’s still some support provided. It’s just not the ideal kind of support for walking on, especially near the edge. It’s probably safe about 12 inches back.
Oh yeah! 😄
The drip edge is causing the water to redirect. You can seal the ends with caulk, paint, and replace them. It’s a bit tricky due to the roof.
Null
Clearly, duct tape is the solution here.
First off, water is flowing from the drip edge directly onto the boards. I think it would be a good idea to eliminate that design and cover the end with soffit and fascia.
.
Just trim off the soft parts, attach new tips, and keep them short this time to keep them out of the water. These rotted mainly because they weren’t painted. It looks like it’s been years since they were last painted.
Hey , it’s been a while! I split my time between here and Hawaii, 6 months each.
Maintaining paint on that aged wood is quite challenging. My folks’ place resembles this, you try painting it, a year later it’s already cracking and flaking. It’s truly tiring!
I’m facing the same issue with a garage I’m currently working on. My plan is to reinforce what’s needed and then construct a ladder soffit that can be attached to the new rafter ends and the garage’s side. After that, I’ll add fascia to the front and enclose everything. It would be best to also redo the roof simultaneously and extend the rafter tail inside by a couple of feet.
Take a look at this.