How can I secure shelves on my accent wall made of scrap wood, and how can I keep my sliding door level and closed with accessible latches for my kids?
I’ve got a couple of problems that need fixing.
1) So, I decided to create an accent wall in my office using scrap wood from the garage, but now my shelves won’t stay put. How can I secure them without making it obvious and without damaging the drywall? I just need them to hold light items, nothing too heavy (unless my cat decides to make an appearance).
2) Next issue is with my sliding door. It’s not staying closed, no matter what I do. It keeps sliding over to the left, even though it looks level. How can I prevent the bottom from straying away from the wall when my kids push on it? And do you have any ideas on how I can keep it in the middle and closed with a latch that can be accessed from both sides? I tried using cabinet magnets at the top of the door, but they’re too far and won’t catch. Any suggestions?
The best option is to use concealed shelf brackets and secure them into studs ideally. If you prefer not to place them where the studs are, use reliable Sheetrock anchors instead.
Oh, thank you so much, ! I’ll give that a shot!
You’re so welcome, !
I recommend using Gorilla construction adhesive for the shelves. I have not encountered this issue with barn doors yet, but I will keep an eye out for it in the future.
For attaching the wall to the floor, your best option is a wall-mounted floor guide. We ran into the same issue. My husband ended up using a multi-tool to cut into the baseboard to attach it.
I think the material we have from might be a bit too short and didn’t quite make it to the door. It could be a trim issue, so I’ll take a closer look. If it’s just a trim problem, I’ll cut out that section and make use of the rest.
Hey Brianna! If those options don’t work, it’s likely that the door was installed too high. I think the floor kit includes different bolts and spacers to raise the wheel.
My partner actually installed it too low at first, then went too high on the second try…and didn’t feel like doing it a third time! 😂
Understands the struggle. The bottom track kit that comes with the door hardware is typically not great. I prefer the kit that Tiffany shared. You can either mount this kit to the base or add a block to elevate it (although it may not look great). It’s important to take action to prevent the door from tilting and coming off the track.
Make sure to discreetly mark the location of the studs before adding more wood slats, so when you install the shelves, they will be secured into the studs. We did this when putting up wainscotting in a hallway by marking the stud locations and planning where to place the main boards and trim boards.
Place quality magnets inside the doors.
No content
Grab two of these, that should do the trick.
Suggested using a latch to keep it closed. What about ensuring it stays in the center and doesn’t drift?
Hey, I just realized something! You don’t have a center stop for the barn doors?
I’ve only been able to locate end stoppers. Where can I get a middle stop? I remember seeing a soft close option, but I believe it was only for the ends.
Have you thought about installing the end stops in the center? It usually comes with the track, but you might need to dismantle some things. Do you know the distance between the roller brackets when closed?
Hey
I think these are the stoppers that were included, I’ll double-check the boxes upstairs and measure the gap between roller brackets.
Hey , could you snap a photo of any additional parts you have?
Put a hot glue dot on the track to easily roll over and ‘lock’ it close
Oh hey , that sounds like something worth trying out!
You have the option to nail the accent wood into studs first and then toe screw the shelf to the accent wood.
Those doors are amazing! Where did you find them?
Shops at Menards 🙂
For mounting the shelf, the best option would be toggle bolt anchors. They are capable of holding over 100 pounds in 1/2 drywall, but it’s always recommended to hang shelves on studs. However, when I have to hang them elsewhere, toggle bolt anchors are my go-to choice.
Enconker 2PCS Hole-Free Barn Door Soft Close Mechanism, Upgraded Design Sliding Door Hardware Spring Buffer Damper, One Way Operation Invisible Door Stopper Adjustable Actuators with Actuator Spacers https://a.co/d/jkXVM0h
Try using these soft stops along with the floor guides mentioned earlier. Otherwise, you’ll have to readjust the doors, which can be a real hassle. These soft stops work wonders, and I’m letting everyone in on my secret here. Plus, they’re affordable and easy to set up.
I’ve learned that when it comes to installing barn door hardware, the quality and price are key. The highly-priced and well-designed options are truly impressive. Simple iron wheels moving along a flat iron bar won’t provide the same precision in door closing.