Can you assist with completing the window installation project?
Asked by Giovanni Storm 
3 months ago
Last Updated: August 30, 2024
Can you give me a hand wrapping up this project with the window?
Have you considered using bull nose tile, perhaps?
There’s a consideration about , but keep in mind not all tiles have bull nose options. Also, it might be a challenge due to how the window is installed. Another thing to consider is the SCHLUTER metal trim – those L-shaped metal bars where you can place the tile inside, but unsure if it will work in this scenario.
Or PVC trim
If I were to do it again, I’d probably go with tiling. But for now, PVC trim is the way to go. Just make sure to seal it up really well.
Hey , I’m having trouble finding where to purchase it.
Hey, is Ygnacio Barinas buying PVC trim?
They have a lot of pvc trim available. While it’s not specifically marketed for bathrooms, you can find it in the trim aisles where they have all the molding, even though it’s plastic.
Tired of trying to find the link, but no luck. It comes in 4-foot lengths.
Ygnacio Barinas also take a look at the bathroom panel section. I have used pvc to rip bathroom trim for entire doorways. It is commonly used for bathroom walls. It’s similar to tongue and groove, but you can reverse it to have a solid side or a smaller groove side. In your situation, you could make it solid, trim all four sides, and then add some pvc trim around it for a nice finish. However, having a window inside a shower can be a real nightmare. They are often removed due to leaks and issues, so make sure to seal it up really well.
You can find it online at either Home Depot or Lowe’s, but you’ll need to order it and have it shipped to you. That’s how it went for me, since most stores didn’t have it in stock.
Hey Ygnacio Barinas, make sure to cut the 1x_ PVC trim pieces to fit custom. Treat it like a standard window trim. Secure the PVC onto the tile using Loctite Power Grab adhesive. Seal the seams with silicone caulk to keep it waterproof. And don’t forget to create a slight slope on the sill to direct water towards the shower.
The Home Depot and my local molding store both have a good variety of options. I had a similar experience with the Colonial trim from Home Depot that matched the existing trim in my house. It sealed up nicely and there haven’t been any issues because of the slanted PVC sill that drains away.
Before, it had PVC trim but
Hey, what’s happening with the tile? Did you end up using 3 different sizes of tile?
Yep :/ but I’m in need of some ideas to figure this out.
Ygnacio Barinas suggested using the larger tiles from behind the toilet to replace the smaller ones of various sizes. It appears to be around 36 or 48, not sure though.
24×48
I simply have to shut the window section
Hey there Ygnacio Barinas
Hey Ygnacio Barinas, you could also grab some flat stock and create a window stool. Just make sure it has a slope. Then you can add a bit of flat stock pvc as a skirt board beneath the stool.
That’s great, I noticed it had that trim before I did it,
Make sure you have a plan before starting to tile.
The problem was that it was an emergency situation, no time to think, my friend. The bathroom was full of mold and mildew, and everything was falling apart. The previous owner never took care of anything here.
Ygnacio Barinas If it’s done incorrectly again, the window tile will lead to the same issue.
Ygnacio Barinas I would recommend using the laticrete brand green rubber material to cover as much of the exposed area as possible. It seems like you might be a bit late to the party, though. I believe they also have a good caulk option available. The Wedi brand caulk/sealer is fantastic. I believe that’s what we used with the laticrete system. Apply the caulk to the foam and all surfaces once they are trimmed back. Allow it to dry, then apply the laticrete rubber coating. It will take some time, but you might still be able to remove some Thinset and insert the schluter trim.
You didn’t actually offer much assistance to the original poster, did you?
Definitely did. Give it another read.
I might get rid of that small window, never seen anything like it before.
Yeah, I was considering it but the bathroom doesn’t have any ventilation.
I’d end up with an even larger hole to fix.
Hey, if that had been taken out before the remodeling, he wouldn’t be dealing with a hole to patch.
Yeah, , I’m actually considering removing that now. But it’s complicated because I believe the previous homeowner added that window for ventilation since the kitchen and bathroom are in the same area and needed better ventilation, at least that’s what I think
Consider installing a vent fan in the bathroom
Has already installed one to combat moisture
Did I show what was there previously?
I must have missed it if Ygnacio Barinas mentioned it.
I decided to scroll down and then back up just to let everyone know about it.
Try using pvc trim instead. If you want to use tile, you should have already done that on the wall.
Rona in Canada has a nice variety of PVC trim options.
You really should fix that tile work. It’s pretty cringy.
Hey guys, so this was my first time attempting to tile. Since this is my own house, I would really appreciate some constructive feedback on my tile work instead of harsh criticism.
Ygnacio Barinas, not too shabby for your first time, right?
I really appreciate your thanks!
Hey, Ygnacio Barinas, that tile work didn’t turn out too great, huh? But, you know, it’s your house, so as long as you’re cool with it…👍🏼
It’s really frustrating when people don’t contribute to solving the issue and instead criticize, which can demotivate others. The admin should definitely address people like that.
You can grab a sill or curb and trim it to size.
I probably would’ve taken out that window, haha.
You can find white trim pieces at Home Depot and Lowe’s that might be suitable. It’s hard to gauge the size of the gap from the photo. They offer cove pieces and bullnose that wrap over the top of the board, which could potentially work. These stores also carry the PVC trim that others have mentioned. Best of luck! P.S. I have the same shower valve/head.
Hey , thanks a lot for the idea, brother!
I just saw large chunks of man-made white quartz pieces at Home Depot. You could purchase those and cut them to size, or look for a nearby stone shop that can customize pieces for your window. My shop frequently creates shower parts.
Having symmetrical grout lines is essential for achieving great tile work. Adjusting the size of tiles to fit can ruin the overall appearance. It seems like you’re not only fixing the window issue but also the entire back wall of the shower, which is completely off and won’t ever look right.
It looks fantastic!
Hmm, interesting.
Have you grouted the corners already? It looks like the window is set back when I zoomed in. You might need a strip of tile around the window. It seems like one tile won’t be enough. We all make mistakes, but it’s okay. You’re definitely making progress from where you began. That’s what counts.
White PVC trim with silicone caulk… and there you have it!
I use PVC trim, liquid nails, and caulk because I’m a painter, not a tiler. It should be durable to avoid needing a callback.
Hey Bec, do you think what we’re doing will be sufficient to avoid needing a callback within a few days?
During small claims court cases, discovered that the answer is definitely yes.
Did an earthquake occur in that location?
When we were tiling the wall, we decided to use a ceramic chair rail type tile to trim around our shower window.
How did you do that? That’s amazing
Ygnacio Barinas hey there, just wanted to share the type of tile we used for this project, you can find it at this link. We went ahead and tiled all the way up to the window, which was made of PVC. To ensure waterproofing, we used the schluter kit beforehand.
Cover the window with some duct tape.
No words needed 🫣🫣🫣🫣😂
I actually have those exact tiles in my bathroom!
Hey, I’m really sorry to hear that. There are definitely therapies available for that.
Should’ve started with the trim first and then build up to it. Make sure to seal the PVC trim securely. I added extension jambs for this one and now it’s completely water tight. ‘t forget to bevel the sill for proper drainage to prevent standing water, as even moisture can collect and form a puddle.
That’s awesome, !
Hey Ygnacio Barinas, it holds paint really well too.
Hey , the PVC trim you picked up from HD is great!
Ygnacio Barinas for sure! I actually used Colonial base PVC from Home Depot in that bathroom too. It’s located in the trim section.
I’m heading over there right now
Ygnacio Barinas hey there! They also carry flat stock in case you need to extend from the window frame to the tile surface.
Sure, go ahead and take it out.
Cut PVC trim to the appropriate size and apply caulk,
Add tile insets inside the trim around the window opening,
I’m wondering, why are there windows in the bathroom? Can they be covered up somehow?
That tile is fabulous!
You might want some help with your design choices too, those tiles are not looking great!
Was the window added after? Why didn’t the tiler finish the trim?
I did it myself for the first time, my first job like that was also a 911 job at home, the window was there
Did it alone
Did it by myself
Having windows in showers is nice, but I don’t think you should attempt to cut into the tile at this stage. Just look for some attractive waterproof trim and frame it. It should work out well. My main worry would be the sill.
I feel the same way! One of the guys in the comments already gave me some ideas to consider.
Best of luck to you, my friend!